Can You Paint A Mirrored Wall

Download Article

While mirrored walls can add a unique style to a room, y'all may be tired of seeing your reflection everywhere. Removing the walls entirely can be expensive, or impossible if you lot hire. Luckily, in that location are several solutions to this problem. For a uncomplicated, temporary set up, hang curtain rods to cover the mirrors. If you prefer a more decorative approach, use peel-and-stick wallpaper on the mirrors. For a more permanent solution, pigment over the mirrors entirely.

one
Mensurate the height and length of each mirror. Utilise a tape mensurate and go the dimensions of the mirror. Write these measurements downwardly and bring them to the store with yous so you get the right-sized curtains.^[one]
- Recollect to measure each mirrored wall that you take to cover.
- This method works whether the mirrors extend from floor to ceiling, or simply cover a portion of the wall.
two
Get a curtain rod and defunction that match your mirror's dimensions. Take your measurements to a hardware or interior design store and find a curtain rod long enough to stretch across the mirror. Then get defunction the correct length and height to hide the walls. If you're covering multiple mirrors, go a curtain rod and drapery for each one.^[2]
- In that location are also adaptable curtain rod designs. Consider trying ane of these if you can't find a rod exactly the correct length.
- There are many curtain choices that use different fabrics, colors, and designs. Choose curtains that match the décor and style of your room.
Advert
3
Marker ii spots on the wall for adhesive hooks. Hanging curtains with adhesive hooks is the best choice for mirrored walls because you tin can't drill holes into mirrors. Start at 1 acme corner and measure 6 inches (fifteen cm) in from the side and 3 inches (seven.6 cm) down from the top. Mark the point with a marker or a piece of record. And so echo the same measurements from the other corner.^[3]
- If the mirror leaves some of the wall exposed, you tin can still use adhesive hooks to avoid putting holes in the wall. If y'all prefer a more secure curtain rod, and then screw hooks into the exposed wall.
4
Adhere the adhesive hooks to the wall. Agglutinative hooks come with a mucilaginous strip, a wall zipper, and a hook. Take the viscous strip and observe the side that says "Wall." This side attaches to the mirror. Skin off the paper on the opposite side and stick it onto the wall zipper. So peel off the paper on the "Wall" side and press information technology confronting the bespeak you marked on the mirror. Hold it for 30 seconds. And so take the hook and slide information technology into the notch on the wall zipper.^[4]
- Repeat this same process for the claw on the opposite side of the mirror.
- Remember to get adhesive hooks designed for curtain utilise. Regular ones may be also small to agree a drapery rod.
- Some adhesive hook brands have unlike zipper methods. Check the instructions on whatsoever product you utilise to confirm the right method.
v

Wait 1 hour for the hooks to stick. Let the adhesive bond to the mirror. If a hook falls off, rub the surface area on the mirror with alcohol and re-attach it. If information technology still won't stick, you may have a lacking adhesive strip.^[5]
6
Loop the curtains onto the curtain rod. While you wait for the hooks to adhere, adhere the curtains to the rod. Nigh curtains take holes on the top. Insert the rod through each pigsty.^{[half dozen]}
- Double check to make sure you inserted the rod into every hole. If you missed whatever, the curtain volition sag.
7
Hang the rod onto the hooks. If yous have a partner to piece of work with, have them hold the rod on the contrary end from you. Then both of yous lift and tuck the rod into the hooks. If you're solitary, hold the rod by the middle and lift information technology upwards. Tilt 1 side upwardly and constrict it into one claw, then lift the other side into the hook.^[7]
- And then spread out the curtains so they cover the mirror.
- Repeat this same installation process for each mirror yous want to embrace.
Advertisement

one
Notice the area of all the mirrors you're covering. Temporary wallpaper comes in sheets or rolls that embrace a specific surface expanse. Measure the height and length of each mirror. So multiply those 2 numbers together to go the area of the mirror.^[8]
- If y'all're covering multiple walls, calculate the area of each and then add together the result together.
- For example, if you're covering a wall that's 8 anxiety (2.4 thousand) long and 6 feet (i.viii g) high, the surface area is 48 square anxiety (4.five mⁱⁱ). If you have 2 walls the aforementioned size, the full area to cover is 96 foursquare anxiety (8.9 g^two).
2
Purchase or lodge plenty temporary wallpaper to cover your mirrors. Temporary wallpaper comes in pre-made rolls with a sticky bankroll. It's substantially a large sticker. Visit a design store or website to order the correct amount of wallpaper to embrace the area of your mirrors.^[9]
- Check the area that a roll of wallpaper covers. You may demand multiple rolls if you're covering a big surface area.
- Temporary wallpaper comes in many different designs. Choose a style that appeals to you lot and fits the décor of your room.
- Sometimes temporary wallpaper tin exist custom made to your specifications. If yous accept a small area to cover, you lot may be able to society one canvas fabricated to those dimensions.
3

Wipe the glass with glass cleaner. Make sure the mirror is completely clean earlier working on it. Spray it with glass cleaner and wipe it down with a clean rag. Permit all of the moisture evaporate so the mirror is dry.^[10]
4
Pare off the summit 3 inches (7.6 cm) of the wallpaper backing. Don't peel off the whole bankroll at once. This makes installation very difficult. Merely pull off three inches (7.six cm) at a time. And then when you've stuck some wallpaper to the mirror, remove a bit more backing.^[11]
- Working with a partner makes this task much easier. One of you lot can pull the bankroll off while the other presses the wallpaper downward.
5
Press the wallpaper downward starting in the top corner of the mirror. Line upward the top corner of the wallpaper with the top corner of the mirror. Brand certain both the top and side edges are even with each other. When the corners are lined upwardly, press down on the wallpaper and stick it to the mirror. Run your hand across the wallpaper and apply smooth pressure level to piece of work out any air bubbles.^[12]
- Don't press downward until the edges are lined up. If y'all pare the wallpaper off afterward making a error, it won't stick as well.
- Stand on a step stool if you lot tin can't accomplish the acme of the mirror.
half-dozen
Peel off more backing and printing the wallpaper down. Once the acme is in place, work down the mirror gradually. Pare off 3 inches (7.6 cm) more backing and printing the wallpaper downwards. Keep working down the mirror in small increments similar this until yous accomplish the bottom.^[13]
- Employ a wallpaper brush or squeegee to smooth out the wallpaper. Press downwardly with even force per unit area against the wallpaper surface.
- Don't rush. If you piece of work too fast, your wallpaper could exist uneven.
- Remember that working with a partner makes this task much easier. You can press down the wallpaper while your partner removes the bankroll, or vice versa.
7
Cut the bottom in a direct line if there is backlog wallpaper. If you're working with a roll of wallpaper, so there will be excess leftover when you reach the bottom of the mirror. Utilize pair of scissors to cut away leftover wallpaper the bottom. Be certain to cutting in a direct line. If there is still some coming off at the lesser, snip along the bottom of the mirror to remove it.^[14]
- Even if y'all ordered a custom-sized wallpaper whorl, there might exist a flake sticking off the side. Employ scissors to trim it abroad.
8
Repeat the procedure beyond the whole mirror. Later completing this starting time row, move over and work on the residual of the mirror. Unroll a bit more wallpaper and line it up with the peak edge and the edge of the first sheet. Remove 3 inches (7.six cm) of backing and press it down, working down the mirror similar before. Work beyond the mirror until you comprehend the whole thing.^[15]
- It's okay if the wallpaper overlaps a lilliputian chip, but attempt to minimize the overlap.
- If the wallpaper has a specific pattern, use it to keep the sheets even with each other. For example, a line pattern might repeat multiple times on each wallpaper gyre. Line up the blueprint when you lay down the next sheet to go on the wallpaper straight.
- Temporary wallpaper is completely removable, so if you don't similar the results, just pare it off.
Advertisement

1
Lay driblet cloths underneath the mirror. Painting is ever a messy job, and then protect your floors. Lay a drib cloth underneath all the mirrors you'll exist working on.^[sixteen]
- Plastic sheets will work likewise.
2
Sand the mirror with a fine-grain sandpaper. This roughs upwards the mirror surface and so paint can stick better. Sand over the whole mirror surface with light, even pressure.^[17]
- Don't endeavor to sand hard and make the whole mirror rough. Just a light sanding works fine.
- For an easier job, tape the sandpaper to a pigment roller. Then coil it over the mirror to sand information technology faster.
3
Clean the glass off with glass cleaner. Sanding may leave some grit or residuum backside. Earlier you paint the mirror, make sure information technology's completely clean. Spray information technology with glass cleaner and wipe it down with a clean rag. Let all of the moisture evaporate so the mirror is dry.^[18]
- If y'all don't have glass cleaner, a clammy rag will likewise option upwards sanding remainder.
4
Apply a primer designed for glass to the mirror. Go to the hardware store and purchase a primer designed to stick on glass. Pour some into a paint tray and wet a roller. So ringlet an even coat of primer out. Employ an up and down motion to lay a line of primer from the bottom to the summit of the mirror. When you finish start a new line, overlap the previous line past one-half to ensure you get good coverage. Keep working until yous cover the whole mirror.^[19]
- Whorl the primer out with even force per unit area, simply don't press hard. Pressing too hard leaves lines on each side of the roller. If you see lines forming, lighten the pressure.
- Don't let the primer baste or pool. Rub away any drips to smooth the surface out.
- Call up to prime all of the mirrors yous're covering.
5
Permit the primer dry for at least 3 hours. The primer needs enough time to dry and so information technology binds to the glass. Drying fourth dimension varies, but give the primer at least 3 hours earlier you paint over it.
- If y'all don't have another roller and pigment tray, clean the tools you used so the paint doesn't mix with primer.
6
Cover the mirror with enamel drinking glass pigment. Enamel paints are designed to adhere to glass. Pour some out into a clean paint tray and dip your roller in. And so utilise the paint with the aforementioned motion and pressure y'all used to curl the primer on. Work lesser to top and roll a line of pigment on the mirror. When you lot commencement a new line, overlap the previous line halfway. Remember to apply light pressure. If you see lines forming, apply less pressure. Work down the mirror until it's fully covered.^[20]
- Paint over every mirror and permit the paint dry for 24 hours. The pigment may dry sooner, but wait at least 24 hours earlier adding a final coat.
- Enamel paint is available from hardware or craft stores.
- Acrylic paint volition as well stick to glass, but it is oftentimes run across-through, and then it's not a good selection to cover the whole mirror with. It's unremarkably used for smaller arts and crafts projects. Utilise it if you want to make smaller designs on the mirror rather than covering it entirely.
seven
Complete the job with a 2nd coat of paint. After 24 hours have passed, apply a final coat of paint with the same motions you used earlier. Let another 24 hours for the topcoat to dry completely and then bask your new pigment job.^[21]
- Remember that mirrors are under this paint. Don't forget and endeavour to hammer any nails into the wall.
Advertisement

Add New Question

Question

How can I use wallpaper creatively?

Emma Oberlander is an Interior Designer and the Owner of Otis Street Pattern in Boston, Massachusetts. She specializes in residential remodels, boutique hospitality design, projection management, and budget design. Emma holds a BA in Advice and Media Studies from Northeastern University and an MA in Interior Compages from The New England School of Art and Design. She has a combined 10 years of projection management feel in the design, marketing, and non-profit industries, both nationally and internationally.

Interior Designer

Practiced Answer

If the ceiling has many angles, you lot can put wallpaper on it. It volition make it look less busy. Besides this, you lot can use paw-painted wallpaper or mural instead of traditional wallpaper.